Bunn LCR-3 Instrukcja Użytkownika

Przeglądaj online lub pobierz Instrukcja Użytkownika dla Sprzęt wodny Bunn LCR-3. Bunn LCR-3 User Manual Instrukcja obsługi

  • Pobierz
  • Dodaj do moich podręczników
  • Drukuj
Przeglądanie stron 0
LCR-3 HV
INSTALLATION & OPERATING GUIDE
BUNN-O-MATIC CORPORATION
POST OFFICE BOX 3227
SPRINGFIELD, ILLINOIS 62708-3227
PHONE: (217) 529-6601 FAX: (217) 529-6644
To ensure you have the latest revision of the Operating Manual, or to view the Illustrated Parts
Catalog, Programming Manual, or Service Manual, please visit the Bunn-O-Matic website, at
www.bunn.com. This is absolutely FREE, and the quickest way to obtain the latest catalog and
manual updates. For Technical Service, contact Bunn-O-Matic Corporation at 1-800-286-6070.
41129.0000H 06/11 ©2008 Bunn-O-Matic Corporation
Przeglądanie stron 0
1 2 3 4 5 6 ... 26 27

Podsumowanie treści

Strona 1 - LCR-3 HV

LCR-3 HVINSTALLATION & OPERATING GUIDEBUNN-O-MATIC CORPORATIONPOST OFFICE BOX 3227SPRINGFIELD, ILLINOIS 62708-3227PHONE: (217) 529-6601 FAX: (2

Strona 2 - 41129 050511

10Rinse Alarm FeaturePeriodic rinsing of the mix chambers and dispense tips is essential for proper maintenance and optimum performance o

Strona 3 - INTRODUCTION

11BIB Empty Lockout FeatureThe dispenser can be set to not dispense product when the concentrate BIB is empty. To enable this feature, first calibrate

Strona 4 - Design Pressures:

12PROGRAMMING THE DISPENSERPress the Right Hidden Switch for 5 sec. to enter the programming menu. Use the Left and Right hidden swi

Strona 5 - PLUMBING REQUIREMENTS

13ENTER PASSWORD(-) 0 (+)SET PASSWORD ?(-) 0 (+)2 OR 3 PRODUCTS? (2) EXIT (3)SELECT UNITSENG EXIT METRICREFRIGERATI

Strona 6 - LEVELING THE DISPENSER

14PROGRAMMING (Continued)BibEMPTY LOCKOUTNO EXIT YESBREW LOCKOUT ?NO EXIT YES ENERGY SAVER MODENO EXIT YESE-SAVER IDLE TIME(-) 4

Strona 7 - DRIP TRAY INSTALLATION

15 LCD DISPLAY ACTION DESCRIPTIONThe following functions are for diagnostic and troubleshooting purposes and typically do not have to be adjust

Strona 8

16 LCD DISPLAY ACTION DESCRIPTIONPROGRAMMING (Continued)XXOVERFLOW > 155(-) EXIT (+) XX REFILL -> 155(-) EXIT (+)WTR START DELAY(-)

Strona 9 - INITIAL FILL & HEAT

17LOADING THE CONCENTRATE1. Thoroughly mix concentrate by vigorously shaking the product Bag-In-Box (BIB).2. Pull the BIB connector through the hole

Strona 10 - Rinse Procedure:

18FILLING CAMBROS OR OTHER LARGE CONTAINERSThe dispenser is designed primarily for containers that will fit under the dispense tip. However, it may be

Strona 11 - Optional 2- Product Operation

19CLEANING & PREVENTATIVE MAINTENANCEGeneral Cleaning and Sanitizing ProceduresNote: The BUNN® Liquid Coffee Dispenser incorporates a “user select

Strona 12 - PROGRAMMING THE DISPENSER

241129 050511BUNN-O-MATIC COMMERCIAL PRODUCT WARRANTYBunn-O-Matic Corp. (“BUNN”) warrants equipment manufactured by it as follows:1) All equipment oth

Strona 13 - PROGRAMMING (Continued)

20REPLACING THE PUMP TUBINGThe pumps and tubing used in this dispenser are designed to give maximum performance and long life. However, the tubes are

Strona 14

21DRAINING THE HOT WATER TANKCAUTION: The dispenser must be disconnected from the power source throughout these steps.1. Disconnect the dispenser fro

Strona 15

22Check Pump & Flow Rate Calibration, refer to Field Calibration ProceduresThe calculated Target RPM for the pump indicated is out of range____ TA

Strona 16

23Troubleshooting (Continued)Service RequiredService RequiredReplace Tubing1. Pump Motor failure2. RPM Sensor failure3. Tubing pinched in rollers__

Strona 17 - LOADING THE CONCENTRATE

24EVAP TEMP SENSOR OUT OF RANGECHECK FOR BADCONNECTIONSCHECK WIRE FORSHORTSCOOL TEMP SENSOR OUT OF RANGECHECK FOR BADCONNECTIONSCHECK WIRE FORSHORTSCO

Strona 18 - OPERATING THE DISPENSER

25Field Calibration of the Concentrate Pumps / Dispenser Flow RatesThe factory set Default Values for the Pump & Dispenser Flow Rates are very acc

Strona 19 - PREVENTIVE MAINTENANCE

26Field Calibrating the Empty BIB WarningThe dispenser will automatically display LEFT, MIDDLE or RIGHT BIB Empty when the corresponding Concentrate B

Strona 20 - REPLACING THE PUMP TUBING

2741129 11060841172.0000C 10/08 © 2008 BUNN-O-MATIC CORPORATION208-240 VOLTS AC3 WIRE + GND SINGLE PHASE 60HZor208-240 VOLTS AC4 WIRE + GND THREE

Strona 21 - DRAINING THE HOT WATER TANK

3INTRODUCTIONAlways follow the Concentrate Manufacturer’s for recommendations for proper Storage and Shelf Life. The product Flavor Profile is extended

Strona 22 - Troubleshooting

4Optional Field Wiring120/208 V, 37.6 A, 7820 W1PH, 3-Wire + GND, 60HZ120/240 V, 43.2 A, 10400 W1PH, 3-Wire + GND, 60HZFOR USE ON INDIVIDUAL BRANCH CI

Strona 23 - Troubleshooting (Continued)

5ELECTRICAL REQUIREMENTSCAUTION: The dispenser must remain disconnected from power source until specified in Electrical Hook-Up.The LCR-3 HV is shipped

Strona 24

6ELECTRICAL HOOK-UPCAUTION: Improper electrical installation will damage electronic components.1. An electrician must provide electrical service as

Strona 25 - 41129 052208

7INSTALLING THE PUMP TUBING (Refer to the Tubing Installation Instructions in side the cabinet door for details.)1. Loosen the thumbscrew securing t

Strona 26

8OPERATING CONTROLS AND INTERFACE1. Master ON/OFF Switch: Disconnects AC Power to the dispenser.2. Hot Water Handle: Pull and Hold to dispense hot w

Strona 27 - 41129 110608

9INITIAL FILL & HEAT1. Confirm the water supply is on.2. Connect the dispenser to the power source.3. Turn the Master ON/OFF Switch ON and selec

Komentarze do niniejszej Instrukcji

Brak uwag