BUNN-O-MATIC CORPORATIONPOST OFFICE BOX 3227SPRINGFIELD, ILLINOIS 62708-3227PHONE: (217) 529-6601 FAX: (217) 529-6644www.bunnomatic.comOPERATING &a
Page 10TROUBLESHOOTINGA troubleshooting guide is provided to suggest probable causes and remedies for the most likely problemsencountered. If the pro
Page 11Will not fill or refillFill or refill does not shut "OFF"(ON/OFF Switch "ON")PROBABLE CAUSE REMEDYPROBLEM1. Power off to br
Page 12TROUBLESHOOTING (cont.)Fill or refill does not shut "OFF" (ON/OFF Switch "ON") (cont)Fill or refill does not shut "OFF
Page 13TROUBLESHOOTING (cont.)PROBLEM PROBABLE CAUSEREMEDYHEATING CIRCUIT1. Display flashing (CDBC-APS/TC/TS/TSR) or ready light flashing(CEZ-APS/TS/T
Page 14TROUBLESHOOTING (cont.)PROBLEM PROBABLE CAUSE REMEDYWater does not heat to propertemperature (cont.)IMPORTANT: Make sure no tem-perature tests
Page 15TROUBLESHOOTING (cont.)PROBLEM PROBABLE CAUSE REMEDYSpitting or excessive steaming(cont.)Brewer is making unusual noises2a. Temperature Probe (
Page 16TROUBLESHOOTING (cont.)PROBLEM PROBABLE CAUSE REMEDYBREWING CIRCUITBrew cycle will not start 1. Display flashing (CDBC-APS/TC/TS/TSR) or ready
Page 17TROUBLESHOOTING (cont.)PROBLEM PROBABLE CAUSE REMEDYBREWING CIRCUIT (cont.)If the start switch (CEZ-APS/TS/TSR) or switch panel (CDBC-APS/TC/TS
Page 18TROUBLESHOOTING (cont.)PROBLEM PROBABLE CAUSE REMEDYBREWING CIRCUIT (cont.)Dripping from sprayheadWeak beverage1. Lime build up2. Dispense valv
Page 19TROUBLESHOOTING (cont.)PROBLEM PROBABLE CAUSE REMEDYBREWING CIRCUIT (cont.)Dry coffee grounds remain in thefunnel1. Sprayhead2. Funnel loadingM
Page 2INTRODUCTIONThis equipment will automatically brew a half-gallon batch of coffee into an awaiting server at the press of abutton. A hot water f
Page 20DIAGNOSTICSIntermittent flashing of the READY indicator (Model CEZ) or the bank of temperature indicators (Model CDBC)indicates that a fault ex
Page 21BUNNMANUFACTURED BY BUNN-O-MATIC CORPORATION SPRINGFIELD, ILLINOIS, U.S.A.MODELS/NVOLTS A.C. AMP
Page 22BUNNMANUFACTURED BY BUNN-O-MATIC CORPORATION SPRINGFIELD, ILLINOIS894 589.253 c128.894 588.855 129.173 588.694 129.517 588.8
Page 23
Page 24
Page 25BUNNMANUFACTURED BY BUNN-O-MATIC CORPORATION SPRINGFIELD, ILLINOIS, U.S.A.MODELS/NVOLTS A.C. AMP
Page 26BUNNMANUFACTURED BY BUNN-O-MATIC CORPORATION SPRINGFIELD, ILLINOIS, U.S.A.MODELS/NVOLTS A.C. AMP
Page 27BUNNMANUFACTURED BY BUNN-O-MATIC CORPORATION SPRINGFIELD, ILLINOIS, U.S.A.MODELS/NVOLTS A.C. AMP
Page 28BUNNMANUFACTURED BY BUNN-O-MATIC CORPORATION SPRINGFIELD, ILLINOIS, U.S.A.MODELS/NVOLTS A.C. AMP
Page 29Location:The tank heater is located inside the tank andsecured to the tank bottom.Test Procedures:1. Disconnect the brewer from the power suppl
Page 3USER NOTICESCarefully read and follow all notices in this manual and on the equipment. All labels on the equipment shouldbe kept in good condit
Page 30P1856SERVICE (cont.)TANK HEATER (Cont.)BLK to Control BoardWHI or RED to TerminalBlockFIG. 14 TANK HEATER WIRING17. Install tank assembly onto
Page 31TRM2J1J2J3J4J5J6J7TRM1CAUTION :WARMERS AND SURFACES ARE HOTSERVICE (cont.)REFILL VALVELocation:The refill valve is located inside the trunk on
Page 32SCHEMATIC WIRING DIAGRAM CDBC-APS/TS/TSR29253 111103EARLY MODELSSOL29257.0000B 12/99 ©1998 BUNN-O-MATIC CORPORATIONTANK HEATERL1GRNGRNRED-
Page 33SCHEMATIC WIRING DIAGRAM CEZ-APS/TS/TSRWHI29341.0000B 6/99 ©1998 BUNN-O-MATIC CORPORATIONWHIWHIBREW SWITCHTANK HEATERGRNRED-14 (MODEL 35)W
Page 34LATE MODELS29253 021604SOLSCHEMATIC WIRING DIAGRAM CDBC 15, 20 & 35 APS/TC/TS29257.0001D 02/04 ©1999 BUNN-O-MATIC CORPORATIONTANK HEA
Page 4ELECTRICAL REQUIREMENTSCAUTION - The brewer must be disconnected from the power source until specified in Initial Set-Up.Model 15 has an attache
Page 5OPERATING CONTROLSModel CEZ-APS/TS/TSRON/OFF SWITCHPlacing the "ON/OFF" switch in the "ON" upper position enables thebrew ci
Page 6INITIAL SET-UP1. Insert an empty funnel into the funnel rails.2. Place an empty server under the funnel.3. Connect the brewer to the power sourc
Page 7CEZ-APS/TS/TSR ADJUSTMENTS & OPTIONAL SETTINGS
Page 8CDBC-APS/TC/TS/TSR ADJUSTMENTS & OPTIONAL SETTINGSSetting Brew TemperatureThe brewer is factory set to brew at 200°F(95°C). To change this s
Page 9CDBC-APS/TC/TS/TSR ADJUSTMENTS & OPTIONAL SETTINGS (cont)Water Sensing Threshold Adjustment Procedure1. Make sure the tank is full of water
Komentarze do niniejszej Instrukcji